Raspberries/mraa
Private
Public Access
2
0
Fork 0
Code Activity

update UP board hardware details and enable ADC

Browse Source 
Some details regarding the UP board are not in-sync with the
final production version of the board.  This update adds an
ADC, removes a UART, and some corrections in the docs for UP.

Signed-off-by: Dan O'Donovan <dan@emutex.com>
Signed-off-by: Brendan Le Foll <brendan.le.foll@intel.com>
This commit is contained in:
Dan O'Donovan
2016-11-18 12:12:08 +00:00
committed by Brendan Le Foll
parent a0332a13b0
commit d2f1b068b7
2 changed files with 56 additions and 21 deletions
Download Patch File Download Diff File Expand all files Collapse all files

29
docs/up.md
View File

@@ -1,11 +1,11 @@
UP Board {#up}
============
UP Board is based on the Intel(R) Atom(TM) x5-Z83xx SoC (formerly Cherry Trail).
It includes 2GB RAM, 16/32GB eMMC flash, 6 USB2.0 ports, 1 USB 3.0 OTG port,
1 Gigabit Ethernet, HDMI and DSI Graphics ports, RTC and a 40-pin I/O header.
The form-factor for the board is based on the Raspberry Pi 2, and can be used
with many of the add-on HAT boards designed for the Raspberry Pi 2.
UP Board is based on the Intel(R) Atom(TM) x5-Z8350 SoC (formerly Cherry Trail).
It includes 1/2/4GB RAM, 16/32/64GB eMMC flash, 6 USB2.0 ports, 1 USB 3.0 OTG
port, 1 Gigabit Ethernet, HDMI and DSI/eDP Graphics ports, RTC and a 40-pin I/O
header. The form-factor for the board is based on the Raspberry Pi 2, and can be
used with many of the add-on HAT boards designed for the Raspberry Pi.
Interface notes
---------------
@@ -25,12 +25,15 @@ granular at higher speeds. E.g. Available speeds include:
25MHz, 12.5MHz, 8.33MHz, 6.25MHz, 5MHz, 4.167MHz, 3.571MHz, 3.125MHz, etc.
Please be aware that speeds in between those steps will be rounded UP to the
next nearest available speed, and capped at 25MHz.
At the time of writing, only a single native chip-select is available (SPI CS0).
2 chip-selects are available, one natively (SPI CS0) and one by GPIO (SPI CS1).
**UART** 2 high-speed UARTs are available, supporting baud rates up to
support baud rates between 300 and 3686400. Hardware flow-control signals are
not exposed, so software flow-control may be needed for rates above 115200.
A console UART is also available but is not fully supported at this time.
**UART** 1 high-speed UART is available, supporting baud rates between 300 and
3686400. Hardware flow-control signals are available on pins 11/36 (RTS/CTS).
**ADC** 1 8-bit single-channel ADC (TI ADC081C021) is available on pin 7.
Please note that a kernel with UP board support is required to enable the I/O
interfaces above. Refer to https://up-community.org for more information.
Pin Mapping
-----------
@@ -48,13 +51,13 @@ Note that there is an enum to use wiringPi style numbers.
| 4 | P1-04 | 5V VCC | | |
| 5 | P1-05 | I2C SCL1 | 3 | I2C1 (/dev/i2c-1) |
| 6 | P1-06 | GND | | |
| 7 | P1-07 | GPIO(4) | 4 | |
| 7 | P1-07 | GPIO(4) | 4 | ADC0 (iio:device0) |
| 8 | P1-08 | UART TX1 | 14 | UART1 (/dev/ttyS1) |
| 9 | P1-09 | GND | | |
| 10 | P1-10 | UART RX1 | 15 | UART1 (/dev/ttyS1) |
| 11 | P1-11 | GPIO(17) | 17 | |
| 12 | P1-12 | I2S CLK | 18 | I2S0 (PCM Audio) |
| 13 | P1-13 | UART RX2 | 27 | UART2 (/dev/ttyS2) |
| 13 | P1-13 | GPIO(27) | 27 | |
| 14 | P1-14 | GND | | |
| 15 | P1-15 | GPIO(22) | 22 | |
| 16 | P1-16 | GPIO(23) | 23 | |
@@ -63,7 +66,7 @@ Note that there is an enum to use wiringPi style numbers.
| 19 | P1-19 | SPI MOSI | 10 | SPI2 (/dev/spidev2.x)|
| 20 | P1-20 | GND | | |
| 21 | P1-21 | SPI MISO | 9 | SPI2 (/dev/spidev2.x)|
| 22 | P1-22 | UART TX2 | 25 | UART2 (/dev/ttyS2) |
| 22 | P1-22 | GPIO(25) | 25 | |
| 23 | P1-23 | SPI SCL | 11 | SPI2 (/dev/spidev2.x)|
| 24 | P1-24 | SPI CS0 | 8 | SPI2 (/dev/spidev2.0)|
| 25 | P1-25 | GND | | |