Raspi2-3_GenImage Commit - r458:17a59b052c06 · Collaboration Tremplin des Sciences

Unknown -

r458:17a59b052c06

parent child

Context file:

r458:17a59b052c06

README.md +1 -1

             Enable Bluetooth to use this. Adds overlay to swap UART0 with UART1. Enabling (slower) Bluetooth and full speed serial console. - RPI `0` `3` `3P` have a fast `hardware UART0` (ttyAMA0) and a `mini UART1` (ttyS0)! RPI `1` `1P` `2` only have a `hardware UART0`. `UART0` is considered better, because is faster and more stable than `mini UART1`. By default the Bluetooth modem is mapped to the `hardware UART0` and `mini UART` is used for console. The `mini UART` is a problem for the serial console, because its baudrate depends on the cpu frequency, which is changing on runtime. Resulting in a volatile baudrate and thus in an unusable serial console.
             ##### `ENABLE_TURBO`=false
-            Enable Turbo mode. This setting locks cpu at highest frequency. As setting ENABLE_CONSOLE=true locks RPI to lowest CPU speed, this is can be used additionally to lock cpu hat max speed. Need a good power supply and probably cooling for the Raspberry PI.
+            VOIDS WARRANTY! Enable Turbo mode - NO overclocking. This setting locks cpu at highest frequency. As setting ENABLE_CONSOLE=true locks RPI to lowest CPU speed, this is can be used additionally to lock cpu hat max speed. Need a good power supply and probably cooling for the Raspberry PI.
             ##### `ENABLE_I2C`=false
             Enable I2C interface on the RPi2/3. Please check the [RPi2/3 pinout diagrams](https://elinux.org/RPi_Low-level_peripherals) to connect the right GPIO pins.

bootstrap.d/13-kernel.sh +2 -1

             		set_kernel_config CONFIG_IP_NF_TARGET_SYNPROXY m
             		set_kernel_config CONFIG_NETFILTER_XT_MATCH_CGROUP m
             		set_kernel_config CONFIG_NETFILTER_XT_MATCH_IPCOMP m
+            		set_kernel_config CONFIG_NETFILTER_XT_MATCH_SOCKET m
             		set_kernel_config CONFIG_NFT_FIB_INET m
             		set_kernel_config CONFIG_NFT_FIB_IPV4 m
             		set_kernel_config CONFIG_NFT_FIB_IPV6 m
             		set_kernel_config CONFIG_NFT_OBJREF m
             		set_kernel_config CONFIG_NFT_RT m
             		set_kernel_config CONFIG_NFT_SET_BITMAP m
-            		set_kernel_config CONFIG_NF_CONNTRACK_TIMEOUT m
+            		set_kernel_config CONFIG_NF_CONNTRACK_TIMEOUT y
             		set_kernel_config CONFIG_NF_LOG_ARP m
             		set_kernel_config CONFIG_NF_SOCKET_IPV4 m
             		set_kernel_config CONFIG_NF_SOCKET_IPV6 m

bootstrap.d/15-rpi-config.sh +3 0

             #locks cpu at max frequency
             if [ "$ENABLE_TURBO" = true ] ; then
               echo "force_turbo=1" >> "${BOOT_DIR}/config.txt"
+              # helps to avoid sdcard corruption when force_turbo is enabled.
+              echo "boot_delay=1" >> "${BOOT_DIR}/config.txt"
             fi
             if [ "$ENABLE_PRINTK" = true ] ; then

bootstrap.d/44-nexmon_monitor_patch.sh +29 -9

@@ -21,7 +21,7 if [ "$ENABLE_NEXMON" = true ] && [ "$ENABLE_WIRELESS" = true ]; then
21	chown -R root:root "${R}"/tmp/nexmon	21	chown -R root:root "${R}"/tmp/nexmon
22		22
23	# Set script Root	23	# Set script Root
24	NEXMON_ROOT="${R}"/tmp/nexmon	24	export NEXMON_ROOT="${R}"/tmp/nexmon
25		25
26	# Remove temporary directory for nexmon sources	26	# Remove temporary directory for nexmon sources
27	rm -fr "${temp_dir}"	27	rm -fr "${temp_dir}"
@@ -35,14 +35,16 if [ "$ENABLE_NEXMON" = true ] && [ "$ENABLE_WIRELESS" = true ]; then
35	# Setup Enviroment: see https://github.com/NoobieDog/nexmon/blob/master/setup_env.sh	35	# Setup Enviroment: see https://github.com/NoobieDog/nexmon/blob/master/setup_env.sh
36	#ARCH="${KERNEL_ARCH}"	36	#ARCH="${KERNEL_ARCH}"
37	#SUBARCH="${KERNEL_ARCH}"	37	#SUBARCH="${KERNEL_ARCH}"
38	KERNEL="${KERNEL_IMAGE}"	38	export KERNEL="${KERNEL_IMAGE}"
39	ARCH=arm	39	export ARCH=arm
40	SUBARCH=arm	40	export SUBARCH=arm
41	CC="${NEXMON_ROOT}"/buildtools/gcc-arm-none-eabi-5_4-2016q2-linux-x86/bin/arm-none-eabi-	41	export CC="${NEXMON_ROOT}"/buildtools/gcc-arm-none-eabi-5_4-2016q2-linux-x86/bin/arm-none-eabi-
42	CCPLUGIN="${NEXMON_ROOT}"/buildtools/gcc-nexmon-plugin/nexmon.so	42	export CCPLUGIN="${NEXMON_ROOT}"/buildtools/gcc-nexmon-plugin/nexmon.so
43	ZLIBFLATE="zlib-flate -compress"	43	export ZLIBFLATE="zlib-flate -compress"
44	Q=@	44	export Q=@
45	NEXMON_SETUP_ENV=1	45	export NEXMON_SETUP_ENV=1
		46	export HOSTUNAME=$(uname -s)
		47	export PLATFORMUNAME=$(uname -m)
46	#. ./setup_env.sh	48	#. ./setup_env.sh
47		49
48	# Make nexmon	50	# Make nexmon
@@ -81,7 +83,25 if [ "$ENABLE_NEXMON" = true ] && [ "$ENABLE_WIRELESS" = true ]; then
81	cp -f "${NEXMON_ROOT}"/patches/bcm43455c0/7_45_154/nexmon/brcmfmac43455-sdio.bin "${WLAN_FIRMWARE_DIR}"/brcmfmac43455-sdio.bin	83	cp -f "${NEXMON_ROOT}"/patches/bcm43455c0/7_45_154/nexmon/brcmfmac43455-sdio.bin "${WLAN_FIRMWARE_DIR}"/brcmfmac43455-sdio.bin
82	fi	84	fi
83		85
		86	# Install kernel module
		87	"${LIB_DIR}"/modules/${KERNEL_VERSION}/
		88
84	#Revert to previous directory	89	#Revert to previous directory
85	cd "${WORKDIR}" \|\| exit	90	cd "${WORKDIR}" \|\| exit
86		91
87	fi	92	fi
		93
		94	## To make the RPi load the modified driver after reboot
		95	# Find the path of the default driver at reboot
		96	# e.g. '/lib/modules/4.14.71-v7+/kernel/drivers/net/wireless/broadcom/brcm80211/brcmfmac/brcmfmac.ko'
		97	PATH_OF_DEFAULT_DRIVER_AT_REBOOT=$(modinfo brcmfmac \| grep -m 1 -oP "^filename:(\s?)(.)$" \| sed -e 's/^filename:$\s$$.$$/\2/g')
		98	# Backup the original driver
		99	mv $PATH_OF_DEFAULT_DRIVER_AT_REBOOT "$PATH_OF_DEFAULT_DRIVER_AT_REBOOT.orig"
		100	# Copy the modified driver (Kernel 4.14)
		101	if is_pizero ; then
		102	cp ./patches/bcm43430a1/7_45_41_46/nexmon/brcmfmac_4.14.y-nexmon/brcmfmac.ko $PATH_OF_DEFAULT_DRIVER_AT_REBOOT
		103	else
		104	cp ./patches/bcm43455c0/7_45_154/nexmon/brcmfmac_4.14.y-nexmon/brcmfmac.ko $PATH_OF_DEFAULT_DRIVER_AT_REBOOT
		105	fi
		106	# Probe all modules and generate new dependency
		107	depmod -a No newline at end of file

functions.sh +1 -1

             #https://github.com/sakaki-/bcmrpi3-kernel-bis/blob/master/conform_config.sh
             set_kernel_config() {
               # flag as $1, value to set as $2, config must exist at "./.config"
-              TGT="${1}"
+              TGT="CONFIG_${1#CONFIG_}"
               REP="${2}"
               if grep -q "^${TGT}[^_]" .config; then
                 sed -i "s/^\(${TGT}=.*\|# ${TGT} is not set\)/${TGT}=${REP}/" .config

General Comments 0

Écrire
Preview

Vous devez vous connecter pour laisser un commentaire. Se connecter maintenant

No TODOs yet

	Site-wide shortcuts
/	Use quick search box
g h	Goto home page
g g	Goto my private gists page
g G	Goto my public gists page
g 0-9	Goto bookmarked items from 0-9
n r	New repository page
n g	New gist page

	Dépôts
g s	Goto summary page
g c	Goto changelog page
g f	Goto files page
g F	Goto files page with file search activated
g p	Goto pull requests page
g o	Goto repository settings
g O	Goto repository access permissions settings
t s	Toggle sidebar on some pages