| @@ -41,12 +41,12 if [ "$ENABLE_UBOOT" = true ] ; then | |||
|
|
41 | 41 | printf "\n# boot u-boot kernel\nkernel=u-boot.bin\n" >> "${BOOT_DIR}/config.txt" |
|
|
42 | 42 | |
|
|
43 | 43 | # Install and setup U-Boot command file |
|
|
44 | install_readonly files/boot/uboot.mkimage "${BOOT_DIR}/uboot.mkimage" | |
|
|
45 | printf "# Set the kernel boot command line\nsetenv bootargs \"earlyprintk ${CMDLINE}\"\n\n$(cat "${BOOT_DIR}"/uboot.mkimage)" > "${BOOT_DIR}/uboot.mkimage" | |
|
|
46 | #Set correkt KERNEL_IMAGE | |
|
|
44 | # Set correct KERNEL_IMAGE in mkfile | |
|
|
47 | 45 | sed -i "s/kernel7.img/$KERNEL_BIN_IMAGE/g" files/boot/uboot.mkimage |
|
|
48 | 46 | #Set correct DTB_FILE |
|
|
49 | 47 | sed -i "s/bcm2709-rpi-2-b.dtb/$DTB_FILE/g" files/boot/uboot.mkimage |
|
|
48 | install_readonly files/boot/uboot.mkimage "${BOOT_DIR}/uboot.mkimage" | |
|
|
49 | printf "# Set the kernel boot command line\nsetenv bootargs \"earlyprintk ${CMDLINE}\"\n\n$(cat "${BOOT_DIR}"/uboot.mkimage)" > "${BOOT_DIR}/uboot.mkimage" | |
|
|
50 | 50 | |
|
|
51 | 51 | if [ "$ENABLE_INITRAMFS" = true ] ; then |
|
|
52 | 52 | # Convert generated initramfs for U-Boot using mkimage |
| @@ -73,10 +73,9 if [ "$ENABLE_UBOOT" = true ] ; then | |||
|
|
73 | 73 | |
|
|
74 | 74 | if [ "$SET_ARCH" = 64 ] ; then |
|
|
75 | 75 | echo "Setting up config.txt to boot 64bit uboot" |
|
|
76 | printf \n# Tell u-boot a 64bit kernel is used\narm_64bit=1\n" >> "${BOOT_DIR}/config.txt" | |
|
|
77 |
|
|
|
|
78 |
|
|
|
|
79 | #to config.txt | |
|
|
76 | printf "\n# Tell u-boot a 64bit kernel is used\narm_64bit=1\n" >> "${BOOT_DIR}/config.txt" | |
|
|
77 | printf "\n# Device tree start addr\ndevice_tree_address=0x100\n" >> "${BOOT_DIR}/config.txt" | |
|
|
78 | printf "\n# Device tree stop adrr\ndevice_tree_end=0x8000\n" >> "${BOOT_DIR}/config.txt" | |
|
|
80 | 79 |
|
|
|
81 | 80 | |
|
|
82 | 81 | # Set mkfile to use the correct mach id |
| @@ -84,8 +83,11 if [ "$ENABLE_UBOOT" = true ] ; then | |||
|
|
84 | 83 | sed -i "s/^\(setenv machid \).*/\10x000008e0/" "${BOOT_DIR}/uboot.mkimage" |
|
|
85 | 84 | fi |
|
|
86 | 85 | |
|
|
86 | # Set mkfile to use the correct dtb file | |
|
|
87 | sed -i "s/^\(setenv dtbfile \).*/\1${DTB_FILE}/" "${BOOT_DIR}/uboot.mkimage" | |
|
|
88 | ||
|
|
87 | 89 | # Set mkfile to use kernel image |
|
|
88 |
sed |
|
|
|
90 | sed "s/^\(fatload mmc 0:1 \${kernel_addr_r} \).*/\1${KERNEL_IMAGE}/" "${BOOT_DIR}/uboot.mkimage" | |
|
|
89 | 91 | |
|
|
90 | 92 | # Remove all leading blank lines |
|
|
91 | 93 | sed -i "/./,\$!d" "${BOOT_DIR}/uboot.mkimage" |
| @@ -340,7 +340,7 fi | |||
|
|
340 | 340 | |
|
|
341 | 341 | # Add device-tree-compiler required for building the U-Boot bootloader |
|
|
342 | 342 | if [ "$ENABLE_UBOOT" = true ] ; then |
|
|
343 | APT_INCLUDES="${APT_INCLUDES},device-tree-compiler,bison,flex" | |
|
|
343 | APT_INCLUDES="${APT_INCLUDES},device-tree-compiler,bison,flex,bc" | |
|
|
344 | 344 | fi |
|
|
345 | 345 | |
|
|
346 | 346 | # Check if root SSH (v2) public key file exists |
General Comments 0
Vous devez vous connecter pour laisser un commentaire.
Se connecter maintenant
