@@ -0,0 +1,21 | |||||
|
1 | add table ip filter | |||
|
2 | add chain ip filter INPUT { type filter hook input priority 0; } | |||
|
3 | add chain ip filter FORWARD { type filter hook forward priority 0; } | |||
|
4 | add chain ip filter OUTPUT { type filter hook output priority 0; } | |||
|
5 | add chain ip filter TCP | |||
|
6 | add chain ip filter UDP | |||
|
7 | add chain ip filter SSH | |||
|
8 | add rule ip filter INPUT icmp type echo-request limit rate 30/minute burst 8 packets counter accept | |||
|
9 | add rule ip filter INPUT icmp type echo-request counter drop | |||
|
10 | add rule ip filter INPUT ct state related,established counter accept | |||
|
11 | add rule ip filter INPUT iifname lo counter accept | |||
|
12 | add rule ip filter INPUT ct state invalid counter drop | |||
|
13 | add rule ip filter INPUT tcp dport 22 ct state new counter jump SSH | |||
|
14 | # -t filter -A SSH -m recent --name sshbf --rttl --rcheck --hitcount 3 --seconds 10 -j DROP | |||
|
15 | # -t filter -A SSH -m recent --name sshbf --rttl --rcheck --hitcount 20 --seconds 1800 -j DROP | |||
|
16 | # -t filter -A SSH -m recent --name sshbf --set -j ACCEPT | |||
|
17 | add rule ip filter INPUT ip protocol udp ct state new counter jump UDP | |||
|
18 | add rule ip filter INPUT tcp flags & fin|syn|rst|ack == syn ct state new counter jump TCP | |||
|
19 | add rule ip filter INPUT ip protocol udp counter reject | |||
|
20 | add rule ip filter INPUT ip protocol tcp counter reject with tcp reset | |||
|
21 | add rule ip filter INPUT counter reject with icmp type prot-unreachable |
@@ -0,0 +1,24 | |||||
|
1 | add table ip6 filter | |||
|
2 | add chain ip6 filter INPUT { type filter hook input priority 0; } | |||
|
3 | add chain ip6 filter FORWARD { type filter hook forward priority 0; } | |||
|
4 | add chain ip6 filter OUTPUT { type filter hook output priority 0; } | |||
|
5 | add chain ip6 filter TCP | |||
|
6 | add chain ip6 filter UDP | |||
|
7 | add chain ip6 filter SSH | |||
|
8 | add rule ip6 filter INPUT rt type 0 counter drop | |||
|
9 | add rule ip6 filter OUTPUT rt type 0 counter drop | |||
|
10 | add rule ip6 filter FORWARD rt type 0 counter drop | |||
|
11 | add rule ip6 filter INPUT meta l4proto ipv6-icmp icmpv6 type echo-request limit rate 30/minute burst 8 packets counter accept | |||
|
12 | add rule ip6 filter INPUT meta l4proto ipv6-icmp icmpv6 type echo-request counter drop | |||
|
13 | add rule ip6 filter INPUT ct state related,established counter accept | |||
|
14 | add rule ip6 filter INPUT iifname lo counter accept | |||
|
15 | add rule ip6 filter INPUT ct state invalid counter drop | |||
|
16 | add rule ip6 filter INPUT tcp dport 22 ct state new counter jump SSH | |||
|
17 | # -t filter -A SSH -m recent --name sshbf --rttl --rcheck --hitcount 3 --seconds 10 -j DROP | |||
|
18 | # -t filter -A SSH -m recent --name sshbf --rttl --rcheck --hitcount 20 --seconds 1800 -j DROP | |||
|
19 | # -t filter -A SSH -m recent --name sshbf --set -j ACCEPT | |||
|
20 | add rule ip6 filter INPUT meta l4proto udp ct state new counter jump UDP | |||
|
21 | add rule ip6 filter INPUT tcp flags & fin|syn|rst|ack == syn ct state new counter jump TCP | |||
|
22 | add rule ip6 filter INPUT meta l4proto udp counter reject with icmpv6 type admin-prohibited | |||
|
23 | add rule ip6 filter INPUT meta l4proto tcp counter reject with icmpv6 type admin-prohibited | |||
|
24 | add rule ip6 filter INPUT counter reject with icmpv6 type admin-prohibited |
@@ -1,5 +1,5 | |||||
1 | ## 介绍 |
|
1 | ## 介绍 | |
2 |
`rpi23-gen-image.sh` 是一个自动生成树莓派2/3系统镜像的脚本工具, 当前支持自动生成32位 armhf 架构的Debian, 发行版本`jessie`, `stretch` 和 `buster`. 树莓派3 64位镜像需要使用特定的配置参数 (```templates/rpi3-stretch-arm64-4.1 |
|
2 | `rpi23-gen-image.sh` 是一个自动生成树莓派2/3系统镜像的脚本工具, 当前支持自动生成32位 armhf 架构的Debian, 发行版本`jessie`, `stretch` 和 `buster`. 树莓派3 64位镜像需要使用特定的配置参数 (```templates/rpi3-stretch-arm64-4.14.y```). | |
3 |
|
3 | |||
4 | ## 构建环境所依赖的包 |
|
4 | ## 构建环境所依赖的包 | |
5 | 一定要安装好下列deb包, 他们是构建过程需要的核心包. 脚本会自动检查, 如果缺少,经用户确认后会自动安装. |
|
5 | 一定要安装好下列deb包, 他们是构建过程需要的核心包. 脚本会自动检查, 如果缺少,经用户确认后会自动安装. |
@@ -1,6 +1,6 | |||||
1 | # rpi23-gen-image |
|
1 | # rpi23-gen-image | |
2 | ## Introduction |
|
2 | ## Introduction | |
3 |
`rpi23-gen-image.sh` is an advanced Debian Linux bootstrapping shell script for generating Debian OS images for Raspberry Pi 2 (RPi2) and Raspberry Pi 3 (RPi3) computers. The script at this time supports the bootstrapping of the Debian (armhf) releases `stretch` and `buster`. Raspberry Pi 3 images are generated for 32-bit mode only. Raspberry Pi 3 64-bit images can be generated using custom configuration parameters (```templates/rpi3-stretch-arm64-4.1 |
|
3 | `rpi23-gen-image.sh` is an advanced Debian Linux bootstrapping shell script for generating Debian OS images for Raspberry Pi 2 (RPi2) and Raspberry Pi 3 (RPi3) computers. The script at this time supports the bootstrapping of the Debian (armhf) releases `stretch` and `buster`. Raspberry Pi 3 images are generated for 32-bit mode only. Raspberry Pi 3 64-bit images can be generated using custom configuration parameters (```templates/rpi3-stretch-arm64-4.14.y```). | |
4 |
|
4 | |||
5 | ## Build dependencies |
|
5 | ## Build dependencies | |
6 | The following list of Debian packages must be installed on the build system because they are essentially required for the bootstrapping process. The script will check if all required packages are installed and missing packages will be installed automatically if confirmed by the user. |
|
6 | The following list of Debian packages must be installed on the build system because they are essentially required for the bootstrapping process. The script will check if all required packages are installed and missing packages will be installed automatically if confirmed by the user. |
@@ -11,29 +11,23 if [ -z "$APT_PROXY" ] ; then | |||||
11 | sed -i "s/\"\"/\"${APT_PROXY}\"/" "${ETC_DIR}/apt/apt.conf.d/10proxy" |
|
11 | sed -i "s/\"\"/\"${APT_PROXY}\"/" "${ETC_DIR}/apt/apt.conf.d/10proxy" | |
12 | fi |
|
12 | fi | |
13 |
|
13 | |||
14 | if [ "$BUILD_KERNEL" = false ] ; then |
|
|||
15 | echo "Downloading precompiled kernel" |
|
|||
16 | echo "error: not configured" |
|
|||
17 | exit 1; |
|
|||
18 | # BUILD_KERNEL=true |
|
|||
19 | else |
|
|||
20 | echo "No precompiled kernel repositories were added" |
|
|||
21 | fi |
|
|||
22 |
|
||||
23 | # Upgrade package index and update all installed packages and changed dependencies |
|
14 | # Upgrade package index and update all installed packages and changed dependencies | |
24 | chroot_exec apt-get -qq -y update |
|
15 | chroot_exec apt-get -qq -y update | |
25 | chroot_exec apt-get -qq -y -u dist-upgrade |
|
16 | chroot_exec apt-get -qq -y -u dist-upgrade | |
26 |
|
17 | |||
|
18 | # Install additional packages | |||
27 | if [ "$APT_INCLUDES_LATE" ] ; then |
|
19 | if [ "$APT_INCLUDES_LATE" ] ; then | |
28 | chroot_exec apt-get -qq -y install "$(echo "$APT_INCLUDES_LATE" |tr , ' ')" |
|
20 | chroot_exec apt-get -qq -y install "$(echo "$APT_INCLUDES_LATE" |tr , ' ')" | |
29 | fi |
|
21 | fi | |
30 |
|
22 | |||
|
23 | # Install Debian custom packages | |||
31 | if [ -d packages ] ; then |
|
24 | if [ -d packages ] ; then | |
32 | for package in packages/*.deb ; do |
|
25 | for package in packages/*.deb ; do | |
33 | cp "$package" "${R}"/tmp |
|
26 | cp "$package" "${R}"/tmp | |
34 | chroot_exec dpkg --unpack /tmp/"$(basename "$package")" |
|
27 | chroot_exec dpkg --unpack /tmp/"$(basename "$package")" | |
35 | done |
|
28 | done | |
36 | fi |
|
29 | fi | |
|
30 | ||||
37 | chroot_exec apt-get -qq -y -f install |
|
31 | chroot_exec apt-get -qq -y -f install | |
38 |
|
32 | |||
39 | chroot_exec apt-get -qq -y check |
|
33 | chroot_exec apt-get -qq -y check |
@@ -107,36 +107,21 if [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then | |||||
107 | # Set permissions |
|
107 | # Set permissions | |
108 | chown -R root:root "${R}/tmp/pi-bluetooth" |
|
108 | chown -R root:root "${R}/tmp/pi-bluetooth" | |
109 |
|
109 | |||
110 | # Install files to chroot |
|
|||
111 |
|
|
110 | # Install tools | |
112 | install_readonly "${R}/tmp/pi-bluetooth/usr/bin/btuart" "${R}/usr/bin/btuart" |
|
111 | install_readonly "${R}/tmp/pi-bluetooth/usr/bin/btuart" "${R}/usr/bin/btuart" | |
113 | install_readonly "${R}/tmp/pi-bluetooth/usr/bin/bthelper" "${R}/usr/bin/bthelper" |
|
112 | install_readonly "${R}/tmp/pi-bluetooth/usr/bin/bthelper" "${R}/usr/bin/bthelper" | |
114 |
|
113 | |||
115 | # Install bluetooth udev rule |
|
114 | # Install bluetooth udev rule | |
116 | install_readonly "${R}/tmp/pi-bluetooth/lib/udev/rules.d/90-pi-bluetooth.rules" "${LIB_DIR}/udev/rules.d/90-pi-bluetooth.rules" |
|
115 | install_readonly "${R}/tmp/pi-bluetooth/lib/udev/rules.d/90-pi-bluetooth.rules" "${LIB_DIR}/udev/rules.d/90-pi-bluetooth.rules" | |
117 | #aur |
|
|||
118 | #install_readonly "${R}/tmp/pi-bluetooth/50-bluetooth-hci-auto-poweron.rules" "${ETC_DIR}/udev/rules.d/50-bluetooth-hci-auto-poweron.rules" |
|
|||
119 |
|
|
116 | ||
120 | # Install Firmware Flash file and apropiate licence |
|
117 | # Install Firmware Flash file and apropiate licence | |
121 | mkdir "${ETC_DIR}/firmware/" |
|
118 | mkdir "${ETC_DIR}/firmware/" | |
122 |
|
119 | |||
123 | #aur https://aur.archlinux.org/packages/pi-bluetooth/ |
|
|||
124 | #install_readonly "${R}/tmp/pi-bluetooth/LICENCE.broadcom_bcm43xx" "${ETC_DIR}/firmware/LICENCE.broadcom_bcm43xx" |
|
|||
125 | #install_readonly "${R}/tmp/pi-bluetooth/BCM43430A1.hcd" "${ETC_DIR}/firmware/BCM43430A1.hcd" |
|
|||
126 |
|
||||
127 | wget -O "${R}/tmp/pi-bluetooth/LICENCE.broadcom_bcm43xx" https://aur.archlinux.org/cgit/aur.git/plain/LICENCE.broadcom_bcm43xx?h=pi-bluetooth |
|
120 | wget -O "${R}/tmp/pi-bluetooth/LICENCE.broadcom_bcm43xx" https://aur.archlinux.org/cgit/aur.git/plain/LICENCE.broadcom_bcm43xx?h=pi-bluetooth | |
128 | wget -O "${R}/tmp/pi-bluetooth/BCM43430A1.hcd" https://aur.archlinux.org/cgit/aur.git/plain/BCM43430A1.hcd?h=pi-bluetooth |
|
121 | wget -O "${R}/tmp/pi-bluetooth/BCM43430A1.hcd" https://aur.archlinux.org/cgit/aur.git/plain/BCM43430A1.hcd?h=pi-bluetooth | |
129 |
|
122 | |||
130 | # Install systemd service for bluetooth |
|
|||
131 | #install_readonly "${R}/tmp/pi-bluetooth/brcm43438.service" "${ETC_DIR}/systemd/system/brcm43438.service" |
|
|||
132 |
|
||||
133 | # Remove temporary directory |
|
|||
134 | #rm -fr "${temp_dir}" |
|
|||
135 |
|
||||
136 | # Get /dev/serial back for compability |
|
123 | # Get /dev/serial back for compability | |
137 | # Raspberry-sys-mod package |
|
|||
138 | wget -O "${ETC_DIR}/udev/rules.d/99-com.rules" https://raw.githubusercontent.com/RPi-Distro/raspberrypi-sys-mods/master/etc.armhf/udev/rules.d/99-com.rules |
|
124 | wget -O "${ETC_DIR}/udev/rules.d/99-com.rules" https://raw.githubusercontent.com/RPi-Distro/raspberrypi-sys-mods/master/etc.armhf/udev/rules.d/99-com.rules | |
139 |
|
||||
140 | fi |
|
125 | fi | |
141 | fi |
|
126 | fi | |
142 |
|
127 |
@@ -103,11 +103,12 if [ "$ENABLE_WIRELESS" = true ] ; then | |||||
103 |
|
103 | |||
104 | # Fetch firmware binary blob for RPI3B+ |
|
104 | # Fetch firmware binary blob for RPI3B+ | |
105 | if [ "$RPI_MODEL" = 3P ] ; then |
|
105 | if [ "$RPI_MODEL" = 3P ] ; then | |
|
106 | # Fetch firmware binary blob for RPi3P | |||
106 | as_nobody wget -q -O "${temp_dir}/brcmfmac43455-sdio.bin" "${WLAN_FIRMWARE_URL}/brcmfmac43455-sdio.bin" |
|
107 | as_nobody wget -q -O "${temp_dir}/brcmfmac43455-sdio.bin" "${WLAN_FIRMWARE_URL}/brcmfmac43455-sdio.bin" | |
107 | as_nobody wget -q -O "${temp_dir}/brcmfmac43455-sdio.txt" "${WLAN_FIRMWARE_URL}/brcmfmac43455-sdio.txt" |
|
108 | as_nobody wget -q -O "${temp_dir}/brcmfmac43455-sdio.txt" "${WLAN_FIRMWARE_URL}/brcmfmac43455-sdio.txt" | |
108 | as_nobody wget -q -O "${temp_dir}/brcmfmac43455-sdio.clm_blob" "${WLAN_FIRMWARE_URL}/brcmfmac43455-sdio.clm_blob" |
|
109 | as_nobody wget -q -O "${temp_dir}/brcmfmac43455-sdio.clm_blob" "${WLAN_FIRMWARE_URL}/brcmfmac43455-sdio.clm_blob" | |
109 | elif [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 0 ] ; then |
|
110 | elif [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 0 ] ; then | |
110 |
# Fetch firmware binary blob for RP |
|
111 | # Fetch firmware binary blob for RPi3 | |
111 | as_nobody wget -q -O "${temp_dir}/brcmfmac43430-sdio.bin" "${WLAN_FIRMWARE_URL}/brcmfmac43430-sdio.bin" |
|
112 | as_nobody wget -q -O "${temp_dir}/brcmfmac43430-sdio.bin" "${WLAN_FIRMWARE_URL}/brcmfmac43430-sdio.bin" | |
112 | as_nobody wget -q -O "${temp_dir}/brcmfmac43430-sdio.txt" "${WLAN_FIRMWARE_URL}/brcmfmac43430-sdio.txt" |
|
113 | as_nobody wget -q -O "${temp_dir}/brcmfmac43430-sdio.txt" "${WLAN_FIRMWARE_URL}/brcmfmac43430-sdio.txt" | |
113 | fi |
|
114 | fi |
@@ -72,7 +72,7 if [ "$ENABLE_UBOOT" = true ] ; then | |||||
72 | printf "\n# 64bit-mode" >> "${BOOT_DIR}/config.txt" |
|
72 | printf "\n# 64bit-mode" >> "${BOOT_DIR}/config.txt" | |
73 | printf "\n# arm_control=0x200 is deprecated https://www.raspberrypi.org/documentation/configuration/config-txt/misc.md" >> "${BOOT_DIR}/config.txt" |
|
73 | printf "\n# arm_control=0x200 is deprecated https://www.raspberrypi.org/documentation/configuration/config-txt/misc.md" >> "${BOOT_DIR}/config.txt" | |
74 | printf "\narm_64bit=1" >> "${BOOT_DIR}/config.txt" |
|
74 | printf "\narm_64bit=1" >> "${BOOT_DIR}/config.txt" | |
75 | #in 64bit uboot booti is used instead of bootz [like in KERNEL_BIN_IMAGE=zImage (armv7)|| Image(armv8)] |
|
75 | ||
76 |
|
|
76 | sed -i "s|bootz|booti|g" "${BOOT_DIR}/uboot.mkimage" | |
77 | fi |
|
77 | fi | |
78 |
|
78 |
@@ -29,6 +29,7 if [ "$ENABLE_VIDEOCORE" = true ] ; then | |||||
29 |
|
29 | |||
30 | # Create build dir |
|
30 | # Create build dir | |
31 | mkdir "${R}"/tmp/userland/build |
|
31 | mkdir "${R}"/tmp/userland/build | |
|
32 | ||||
32 | # push us to build directory |
|
33 | # push us to build directory | |
33 | pushd "${R}"/tmp/userland/build |
|
34 | pushd "${R}"/tmp/userland/build | |
34 |
|
35 | |||
@@ -46,6 +47,7 if [ "$ENABLE_VIDEOCORE" = true ] ; then | |||||
46 |
|
47 | |||
47 | #build userland |
|
48 | #build userland | |
48 | make -j "$(nproc)" |
|
49 | make -j "$(nproc)" | |
|
50 | ||||
49 | #pop us out of build dir |
|
51 | #pop us out of build dir | |
50 | popd |
|
52 | popd | |
51 | fi |
|
53 | fi |
@@ -146,7 +146,7 ENABLE_REDUCE=${ENABLE_REDUCE:=false} | |||||
146 | ENABLE_UBOOT=${ENABLE_UBOOT:=false} |
|
146 | ENABLE_UBOOT=${ENABLE_UBOOT:=false} | |
147 | UBOOTSRC_DIR=${UBOOTSRC_DIR:=""} |
|
147 | UBOOTSRC_DIR=${UBOOTSRC_DIR:=""} | |
148 | ENABLE_FBTURBO=${ENABLE_FBTURBO:=false} |
|
148 | ENABLE_FBTURBO=${ENABLE_FBTURBO:=false} | |
149 |
ENABLE_VIDEOCORE=${ENABLE_VIDEOCORE:= |
|
149 | ENABLE_VIDEOCORE=${ENABLE_VIDEOCORE:=false} | |
150 | VIDEOCORESRC_DIR=${VIDEOCORESRC_DIR:=""} |
|
150 | VIDEOCORESRC_DIR=${VIDEOCORESRC_DIR:=""} | |
151 | FBTURBOSRC_DIR=${FBTURBOSRC_DIR:=""} |
|
151 | FBTURBOSRC_DIR=${FBTURBOSRC_DIR:=""} | |
152 | ENABLE_HARDNET=${ENABLE_HARDNET:=false} |
|
152 | ENABLE_HARDNET=${ENABLE_HARDNET:=false} | |
@@ -208,29 +208,17 COMPILER_PACKAGES="" | |||||
208 |
|
208 | |||
209 | set +x |
|
209 | set +x | |
210 |
|
210 | |||
211 | #If init and systemd-sysv are wanted e.g. halt/reboot/shutdown scripts |
|
211 | # Setup architecture specific settings | |
212 | if [ "$ENABLE_SYSVINIT" = false ] ; then |
|
|||
213 | APT_EXCLUDES="--exclude=${APT_EXCLUDES},init,systemd-sysv" |
|
|||
214 | fi |
|
|||
215 |
|
||||
216 | #Check if apt-cacher-ng has its default port open on and set APT_PROXY |
|
|||
217 | if [ -n "$(lsof -i :3142)" ] ; then |
|
|||
218 | HTTP_PROXY=http://127.0.0.1:3142/ |
|
|||
219 | fi |
|
|||
220 |
|
||||
221 | #make script easier and more stable to use with convenient setup switch. Just setup SET_ARCH and RPI_MODEL and your good to go! |
|
|||
222 | if [ -n "$SET_ARCH" ] ; then |
|
212 | if [ -n "$SET_ARCH" ] ; then | |
223 | echo "Setting Architecture specific settings" |
|
213 | ||
224 | ################################## |
|
214 | # 64 bit configuration | |
225 | # 64 bit config |
|
|||
226 | ################################## |
|
|||
227 | if [ "$SET_ARCH" = 64 ] ; then |
|
215 | if [ "$SET_ARCH" = 64 ] ; then | |
228 | echo "64 bit mode selected - Setting up enviroment" |
|
216 | # General 64 bit depended settings | |
229 | # 64 bit depended settings |
|
|||
230 | QEMU_BINARY=${QEMU_BINARY:=/usr/bin/qemu-aarch64-static} |
|
217 | QEMU_BINARY=${QEMU_BINARY:=/usr/bin/qemu-aarch64-static} | |
231 | KERNEL_ARCH=${KERNEL_ARCH:=arm64} |
|
218 | KERNEL_ARCH=${KERNEL_ARCH:=arm64} | |
232 | KERNEL_BIN_IMAGE=${KERNEL_BIN_IMAGE:="Image"} |
|
219 | KERNEL_BIN_IMAGE=${KERNEL_BIN_IMAGE:="Image"} | |
233 |
|
220 | |||
|
221 | # Board specific settings | |||
234 | if [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then |
|
222 | if [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then | |
235 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-arm64" |
|
223 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-arm64" | |
236 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcmrpi3_defconfig} |
|
224 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcmrpi3_defconfig} | |
@@ -243,27 +231,24 if [ -n "$SET_ARCH" ] ; then | |||||
243 | fi |
|
231 | fi | |
244 | fi |
|
232 | fi | |
245 |
|
233 | |||
246 | ################################## |
|
234 | # 32 bit configuration | |
247 | # 32 bit config |
|
|||
248 | ################################## |
|
|||
249 | if [ "$SET_ARCH" = 32 ] ; then |
|
235 | if [ "$SET_ARCH" = 32 ] ; then | |
250 | echo "32 bit mode selected - Setting up enviroment" |
|
236 | # General 32 bit dependend settings | |
251 | #General 32bit configuration |
|
|||
252 | QEMU_BINARY=${QEMU_BINARY:=/usr/bin/qemu-arm-static} |
|
237 | QEMU_BINARY=${QEMU_BINARY:=/usr/bin/qemu-arm-static} | |
253 | KERNEL_ARCH=${KERNEL_ARCH:=arm} |
|
238 | KERNEL_ARCH=${KERNEL_ARCH:=arm} | |
254 | KERNEL_BIN_IMAGE=${KERNEL_BIN_IMAGE:="zImage"} |
|
239 | KERNEL_BIN_IMAGE=${KERNEL_BIN_IMAGE:="zImage"} | |
255 |
|
240 | |||
256 | #Raspberry setting grouped by board compability |
|
241 | # Hardware specific settings | |
257 | if [ "$RPI_MODEL" = 0 ] || [ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] ; then |
|
242 | if [ "$RPI_MODEL" = 0 ] || [ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] ; then | |
258 | echo "Setting settings for bcm2835 Raspberry PI boards" |
|
|||
259 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-armel" |
|
243 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-armel" | |
260 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcmrpi_defconfig} |
|
244 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcmrpi_defconfig} | |
261 | RELEASE_ARCH=${RELEASE_ARCH:=armel} |
|
245 | RELEASE_ARCH=${RELEASE_ARCH:=armel} | |
262 | KERNEL_IMAGE=${KERNEL_IMAGE:=kernel.img} |
|
246 | KERNEL_IMAGE=${KERNEL_IMAGE:=kernel.img} | |
263 | CROSS_COMPILE=${CROSS_COMPILE:=arm-linux-gnueabi-} |
|
247 | CROSS_COMPILE=${CROSS_COMPILE:=arm-linux-gnueabi-} | |
264 | fi |
|
248 | fi | |
|
249 | ||||
|
250 | # Hardware specific settings | |||
265 | if [ "$RPI_MODEL" = 2 ] || [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then |
|
251 | if [ "$RPI_MODEL" = 2 ] || [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then | |
266 | echo "Setting settings for bcm2837 Raspberry PI boards" |
|
|||
267 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-armhf" |
|
252 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-armhf" | |
268 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcm2709_defconfig} |
|
253 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcm2709_defconfig} | |
269 | RELEASE_ARCH=${RELEASE_ARCH:=armhf} |
|
254 | RELEASE_ARCH=${RELEASE_ARCH:=armhf} | |
@@ -276,9 +261,7 else | |||||
276 | echo "error: Please set '32' or '64' as value for SET_ARCH" |
|
261 | echo "error: Please set '32' or '64' as value for SET_ARCH" | |
277 | exit 1 |
|
262 | exit 1 | |
278 | fi |
|
263 | fi | |
279 |
|
264 | # Device specific configuration and U-Boot configuration | ||
280 | #Device specific configuration and uboot-config |
|
|||
281 | echo "Select DTB-File" |
|
|||
282 | case "$RPI_MODEL" in |
|
265 | case "$RPI_MODEL" in | |
283 | 0) |
|
266 | 0) | |
284 | DTB_FILE=${DTB_FILE:=bcm2708-rpi-0-w.dtb} |
|
267 | DTB_FILE=${DTB_FILE:=bcm2708-rpi-0-w.dtb} | |
@@ -329,6 +312,7 if [ -n "$DISABLE_UNDERVOLT_WARNINGS" ] ; then | |||||
329 | fi |
|
312 | fi | |
330 | fi |
|
313 | fi | |
331 |
|
314 | |||
|
315 | # Add cmake to compile videocore sources | |||
332 | if [ "$ENABLE_VIDEOCORE" = true ] ; then |
|
316 | if [ "$ENABLE_VIDEOCORE" = true ] ; then | |
333 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} cmake" |
|
317 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} cmake" | |
334 | fi |
|
318 | fi | |
@@ -536,6 +520,21 if [ "$ENABLE_REDUCE" = true ] ; then | |||||
536 | fi |
|
520 | fi | |
537 | fi |
|
521 | fi | |
538 |
|
522 | |||
|
523 | # Configure systemd-sysv exclude to make halt/reboot/shutdown scripts available | |||
|
524 | if [ "$ENABLE_SYSVINIT" = false ] ; then | |||
|
525 | APT_EXCLUDES="--exclude=${APT_EXCLUDES},init,systemd-sysv" | |||
|
526 | fi | |||
|
527 | ||||
|
528 | # Check if kernel is getting compiled | |||
|
529 | if [ "$BUILD_KERNEL" = false ] ; then | |||
|
530 | echo "Downloading precompiled kernel" | |||
|
531 | echo "error: not configured" | |||
|
532 | exit 1; | |||
|
533 | # BUILD_KERNEL=true | |||
|
534 | else | |||
|
535 | echo "No precompiled kernel repositories were added" | |||
|
536 | fi | |||
|
537 | ||||
539 | # Configure kernel sources if no KERNELSRC_DIR |
|
538 | # Configure kernel sources if no KERNELSRC_DIR | |
540 | if [ "$BUILD_KERNEL" = true ] && [ -z "$KERNELSRC_DIR" ] ; then |
|
539 | if [ "$BUILD_KERNEL" = true ] && [ -z "$KERNELSRC_DIR" ] ; then | |
541 | KERNELSRC_CONFIG=true |
|
540 | KERNELSRC_CONFIG=true |
@@ -11,5 +11,5 QEMU_BINARY=/usr/bin/qemu-aarch64-static | |||||
11 | KERNEL_DEFCONFIG=bcmrpi3_defconfig |
|
11 | KERNEL_DEFCONFIG=bcmrpi3_defconfig | |
12 | KERNEL_BIN_IMAGE=Image |
|
12 | KERNEL_BIN_IMAGE=Image | |
13 | KERNEL_IMAGE=kernel8.img |
|
13 | KERNEL_IMAGE=kernel8.img | |
14 |
KERNEL_BRANCH=rpi-4.1 |
|
14 | KERNEL_BRANCH=rpi-4.14.y | |
15 | ENABLE_WIRELESS=true |
|
15 | ENABLE_WIRELESS=true |
1 | NO CONTENT: file was removed |
|
NO CONTENT: file was removed |
1 | NO CONTENT: file was removed |
|
NO CONTENT: file was removed |
General Comments 0
Vous devez vous connecter pour laisser un commentaire.
Se connecter maintenant