| @@ -255,32 +255,31 set +x | |||||
| 255 |
|
255 | |||
| 256 | # Set Raspberry Pi model specific configuration |
|
256 | # Set Raspberry Pi model specific configuration | |
| 257 | if [ "$RPI_MODEL" = 0 ] ; then |
|
257 | if [ "$RPI_MODEL" = 0 ] ; then | |
| 258 |
DTB_FILE=${RPI |
|
258 | DTB_FILE=${RPI0_DTB_FILE} | |
| 259 |
UBOOT_CONFIG=${RPI |
|
259 | UBOOT_CONFIG=${RPI0_UBOOT_CONFIG} | |
| 260 | elif [ "$RPI_MODEL" = 1 ] ; then |
|
260 | elif [ "$RPI_MODEL" = 1 ] ; then | |
| 261 |
DTB_FILE=${RPI |
|
261 | DTB_FILE=${RPI1_DTB_FILE} | |
| 262 |
UBOOT_CONFIG=${RPI |
|
262 | UBOOT_CONFIG=${RPI1_UBOOT_CONFIG} | |
| 263 | elif [ "$RPI_MODEL" = 1P ] ; then |
|
263 | elif [ "$RPI_MODEL" = 1P ] ; then | |
| 264 |
DTB_FILE=${RPI |
|
264 | DTB_FILE=${RPI1P_DTB_FILE} | |
| 265 |
UBOOT_CONFIG=${RPI |
|
265 | UBOOT_CONFIG=${RPI1P_UBOOT_CONFIG} | |
| 266 | elif [ "$RPI_MODEL" = 2 ] ; then |
|
266 | elif [ "$RPI_MODEL" = 2 ] ; then | |
| 267 | DTB_FILE=${RPI2_DTB_FILE} |
|
267 | DTB_FILE=${RPI2_DTB_FILE} | |
| 268 | UBOOT_CONFIG=${RPI2_UBOOT_CONFIG} |
|
268 | UBOOT_CONFIG=${RPI2_UBOOT_CONFIG} | |
| 269 | elif [ "$RPI_MODEL" = 3 ] ; then |
|
269 | elif [ "$RPI_MODEL" = 3 ] ; then | |
| 270 | DTB_FILE=${RPI3_DTB_FILE} |
|
270 | DTB_FILE=${RPI3_DTB_FILE} | |
| 271 | UBOOT_CONFIG=${RPI3_UBOOT_CONFIG} |
|
271 | UBOOT_CONFIG=${RPI3_UBOOT_CONFIG} | |
| 272 | BUILD_KERNEL=true |
|
|||
| 273 | elif [ "$RPI_MODEL" = 3P ] ; then |
|
272 | elif [ "$RPI_MODEL" = 3P ] ; then | |
| 274 | DTB_FILE=${RPI3P_DTB_FILE} |
|
273 | DTB_FILE=${RPI3P_DTB_FILE} | |
| 275 | UBOOT_CONFIG=${RPI3P_UBOOT_CONFIG} |
|
274 | UBOOT_CONFIG=${RPI3P_UBOOT_CONFIG} | |
| 276 | BUILD_KERNEL=true |
|
|||
| 277 | else |
|
275 | else | |
| 278 | echo "error: Raspberry Pi model ${RPI_MODEL} is not supported!" |
|
276 | echo "error: Raspberry Pi model ${RPI_MODEL} is not supported!" | |
| 279 | exit 1 |
|
277 | exit 1 | |
| 280 | fi |
|
278 | fi | |
| 281 |
|
279 | |||
| 282 | # Check if the internal wireless interface is supported by the RPi model |
|
280 | # Check if the internal wireless interface is supported by the RPi model | |
| 283 | if [ "$ENABLE_WIRELESS" = true ] && [ "$RPI_MODEL" = 2 ]; then |
|
281 | if [ "$ENABLE_WIRELESS" = true ] && ([ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] || [ "$RPI_MODEL" = 2 ]); then | |
|
|
282 | ||||
| 284 | echo "error: The selected Raspberry Pi model has no internal wireless interface" |
|
283 | echo "error: The selected Raspberry Pi model has no internal wireless interface" | |
| 285 | exit 1 |
|
284 | exit 1 | |
| 286 | fi |
|
285 | fi | |
General Comments 0
Vous devez vous connecter pour laisser un commentaire.
Se connecter maintenant
