| @@ -0,0 +1,1 | |||
|
|
1 | kernel.printk = 3 4 1 3 No newline at end of file | |
| @@ -0,0 +1,33 | |||
|
|
1 | SUBSYSTEM=="input", GROUP="input", MODE="0660" | |
|
|
2 | SUBSYSTEM=="i2c-dev", GROUP="i2c", MODE="0660" | |
|
|
3 | SUBSYSTEM=="spidev", GROUP="spi", MODE="0660" | |
|
|
4 | SUBSYSTEM=="bcm2835-gpiomem", GROUP="gpio", MODE="0660" | |
|
|
5 | ||
|
|
6 | SUBSYSTEM=="gpio", GROUP="gpio", MODE="0660" | |
|
|
7 | SUBSYSTEM=="gpio*", PROGRAM="/bin/sh -c '\ | |
|
|
8 | chown -R root:gpio /sys/class/gpio && chmod -R 770 /sys/class/gpio;\ | |
|
|
9 | chown -R root:gpio /sys/devices/virtual/gpio && chmod -R 770 /sys/devices/virtual/gpio;\ | |
|
|
10 | chown -R root:gpio /sys$devpath && chmod -R 770 /sys$devpath\ | |
|
|
11 | '" | |
|
|
12 | ||
|
|
13 | KERNEL=="ttyAMA[01]", PROGRAM="/bin/sh -c '\ | |
|
|
14 | ALIASES=/proc/device-tree/aliases; \ | |
|
|
15 | if cmp -s $ALIASES/uart0 $ALIASES/serial0; then \ | |
|
|
16 | echo 0;\ | |
|
|
17 | elif cmp -s $ALIASES/uart0 $ALIASES/serial1; then \ | |
|
|
18 | echo 1; \ | |
|
|
19 | else \ | |
|
|
20 | exit 1; \ | |
|
|
21 | fi\ | |
|
|
22 | '", SYMLINK+="serial%c" | |
|
|
23 | ||
|
|
24 | KERNEL=="ttyS0", PROGRAM="/bin/sh -c '\ | |
|
|
25 | ALIASES=/proc/device-tree/aliases; \ | |
|
|
26 | if cmp -s $ALIASES/uart1 $ALIASES/serial0; then \ | |
|
|
27 | echo 0; \ | |
|
|
28 | elif cmp -s $ALIASES/uart1 $ALIASES/serial1; then \ | |
|
|
29 | echo 1; \ | |
|
|
30 | else \ | |
|
|
31 | exit 1; \ | |
|
|
32 | fi \ | |
|
|
33 | '", SYMLINK+="serial%c" | |
| @@ -153,7 +153,19 Set the IP address for the second NTP server. | |||
|
|
153 | 153 | |
|
|
154 | 154 | #### Basic system features: |
|
|
155 | 155 | ##### `ENABLE_CONSOLE`=true |
|
|
156 | Enable serial console interface. Recommended if no monitor or keyboard is connected to the RPi2/3. In case of problems fe. if the network (auto) configuration failed - the serial console can be used to access the system. | |
|
|
156 | Enable serial console interface. Recommended if no monitor or keyboard is connected to the RPi2/3. In case of problems fe. if the network (auto) configuration failed - the serial console can be used to access the system. On RPI `0` `3` `3P` the CPU speed is locked at lowest speed. | |
|
|
157 | ||
|
|
158 | ##### `ENABLE_PRINTK`=false | |
|
|
159 | Enables printing kernel messages to konsole. printk is `3 4 1 3` as in raspbian. | |
|
|
160 | ||
|
|
161 | ##### `ENABLE_BLUETOOTH`=false | |
|
|
162 | Enable onboard Bluetooth interface on the RPi0/3/3P. See: https://spellfoundry.com/2016/05/29/configuring-gpio-serial-port-raspbian-jessie-including-pi-3/ | |
|
|
163 | ||
|
|
164 | ##### `ENABLE_MINIUART_OVERLAY`=false | |
|
|
165 | Enable Bluetooth to use this. Adds overlay to swap UART0 with UART1. Enabling (slower) Bluetooth and full speed serial console. - RPI `0` `3` `3P` have a fast `hardware UART0` (ttyAMA0) and a `mini UART1` (ttyS0)! RPI `1` `1P` `2` only have a `hardware UART0`. `UART0` is considered better, because is faster and more stable than `mini UART1`. By default the Bluetooth modem is mapped to the `hardware UART0` and `mini UART` is used for console. The `mini UART` is a problem for the serial console, because its baudrate depends on the cpu frequency, which is changing on runtime. Resulting in a volatile baudrate and thus in an unusable serial console. | |
|
|
166 | ||
|
|
167 | ##### `ENABLE_TURBO`=false | |
|
|
168 | Enable Turbo mode. This setting locks cpu at highest frequency. As setting ENABLE_CONSOLE=true locks RPI to lowest CPU speed, this is can be used additionally to lock cpu hat max speed. Need a good power supply and probably cooling for the Raspberry PI. | |
|
|
157 | 169 | |
|
|
158 | 170 | ##### `ENABLE_I2C`=false |
|
|
159 | 171 | Enable I2C interface on the RPi2/3. Please check the [RPi2/3 pinout diagrams](https://elinux.org/RPi_Low-level_peripherals) to connect the right GPIO pins. |
| @@ -173,9 +185,6 Allow the installation of non-free Debian packages that do not comply with the D | |||
|
|
173 | 185 | ##### `ENABLE_WIRELESS`=false |
|
|
174 | 186 | Download and install the [closed-source firmware binary blob](https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm) that is required to run the internal wireless interface of the Raspberry Pi model `3`. This parameter is ignored if the specified `RPI_MODEL` is not `3`. |
|
|
175 | 187 | |
|
|
176 | ##### `ENABLE_BLUETOOTH`=false | |
|
|
177 | Enable Bluetooth interface on the RPi0/3/3P. | |
|
|
178 | ||
|
|
179 | 188 | ##### `ENABLE_RSYSLOG`=true |
|
|
180 | 189 | If set to false, disable and uninstall rsyslog (so logs will be available only in journal files) |
|
|
181 | 190 | |
| @@ -89,13 +89,8 if [ "$BUILD_KERNEL" = true ] ; then | |||
|
|
89 | 89 | #Switch to KERNELSRC_DIR |
|
|
90 | 90 | cd "${KERNEL_DIR}" |
|
|
91 | 91 | |
|
|
92 | # GPL v2.0 | |
|
|
93 | #https://github.com/sakaki-/bcmrpi3-kernel-bis/blob/master/conform_config.sh | |
|
|
92 | # enable ZSWAP see https://askubuntu.com/a/472227 or https://wiki.archlinux.org/index.php/zswap | |
|
|
94 | 93 | if [ "$KERNEL_ZSWAP" = true ] && { [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; } ; then |
|
|
95 | # enable ZSWAP support for better performance during large builds etc. | |
|
|
96 | # requires activation via kernel parameter or sysfs | |
|
|
97 | # see e.g. https://askubuntu.com/a/472227 for a summary of ZSWAP (vs ZRAM etc.) | |
|
|
98 | # and e.g. https://wiki.archlinux.org/index.php/zswap for parameters etc. | |
|
|
99 | 94 |
|
|
|
100 | 95 | set_kernel_config ZSWAP y |
|
|
101 | 96 | set_kernel_config ZBUD y |
| @@ -104,16 +99,15 if [ "$BUILD_KERNEL" = true ] ; then | |||
|
|
104 | 99 | set_kernel_config PGTABLE_MAPPING y |
|
|
105 | 100 | fi |
|
|
106 | 101 | |
|
|
102 | # enable basic KVM support; see https://www.raspberrypi.org/forums/viewtopic.php?f=63&t=210546&start=25#p1300453 | |
|
|
107 | 103 | if [ "$KERNEL_VIRT" = true ] && { [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; } ; then |
|
|
108 | # enable basic KVM support; see e.g. | |
|
|
109 | # https://www.raspberrypi.org/forums/viewtopic.php?f=63&t=210546&start=25#p1300453 | |
|
|
110 | 104 |
|
|
|
111 | 105 | set_kernel_config KVM y |
|
|
112 | 106 | set_kernel_config VHOST_NET m |
|
|
113 | 107 | set_kernel_config VHOST_CROSS_ENDIAN_LEGACY y |
|
|
114 | 108 | fi |
|
|
115 | #See https://github.com/raspberrypi/linux/issues/2177#issuecomment-354647406 | |
|
|
116 | # Netfilter kernel support | |
|
|
109 | ||
|
|
110 | # Netfilter kernel support See https://github.com/raspberrypi/linux/issues/2177#issuecomment-354647406 | |
|
|
117 | 111 | if [ "$KERNEL_NF" = true ] && { [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; } ; then |
|
|
118 | 112 | set_kernel_config CONFIG_NETFILTER_XTABLES m |
|
|
119 | 113 | set_kernel_config CONFIG_NF_DUP_NETDEV m |
| @@ -205,9 +199,7 if [ "$BUILD_KERNEL" = true ] ; then | |||
|
|
205 | 199 | set_kernel_config NETFILTER_XTABLES m |
|
|
206 | 200 | fi |
|
|
207 | 201 | |
|
|
208 | #https://groups.google.com/forum/#!topic/linux.gentoo.user/_2aSc_ztGpA | |
|
|
209 | #https://github.com/torvalds/linux/blob/master/init/Kconfig#L848 | |
|
|
210 | # Enables BPF syscall for systemd-journald | |
|
|
202 | # Enables BPF syscall for systemd-journald see https://github.com/torvalds/linux/blob/master/init/Kconfig#L848 or https://groups.google.com/forum/#!topic/linux.gentoo.user/_2aSc_ztGpA | |
|
|
211 | 203 | if [ "$KERNEL_BPF" = true ] && { [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; } ; then |
|
|
212 | 204 | set_kernel_config CONFIG_BPF_SYSCALL y |
|
|
213 | 205 | set_kernel_config CONFIG_CGROUP_BPF y |
| @@ -51,8 +51,6 else | |||
|
|
51 | 51 | fi |
|
|
52 | 52 | fi |
|
|
53 | 53 | |
|
|
54 | ||
|
|
55 | ||
|
|
56 | 54 | # Add encrypted root partition to cmdline.txt |
|
|
57 | 55 | if [ "$ENABLE_CRYPTFS" = true ] ; then |
|
|
58 | 56 | if [ "$ENABLE_SPLITFS" = true ] ; then |
| @@ -66,47 +64,24 if [ "$ENABLE_CRYPTFS" = true ] ; then | |||
|
|
66 | 64 | fi |
|
|
67 | 65 | fi |
|
|
68 | 66 | |
|
|
69 | # Add serial console support | |
|
|
70 |
|
|
|
|
71 | # CMDLINE="${CMDLINE} console=ttyAMA0,115200 kgdboc=ttyAMA0,115200" | |
|
|
72 | #fi | |
|
|
73 | ||
|
|
74 | # Remove IPv6 networking support | |
|
|
75 | if [ "$ENABLE_IPV6" = false ] ; then | |
|
|
76 | CMDLINE="${CMDLINE} ipv6.disable=1" | |
|
|
67 | #locks cpu at max frequency | |
|
|
68 | if [ "$ENABLE_TURBO" = true ] ; then | |
|
|
69 | echo "force_turbo=1" >> "${BOOT_DIR}/config.txt" | |
|
|
77 | 70 | fi |
|
|
78 | 71 | |
|
|
79 | # Automatically assign predictable network interface names | |
|
|
80 | if [ "$ENABLE_IFNAMES" = false ] ; then | |
|
|
81 | CMDLINE="${CMDLINE} net.ifnames=0" | |
|
|
82 | else | |
|
|
83 | CMDLINE="${CMDLINE} net.ifnames=1" | |
|
|
72 | if [ "$ENABLE_PRINTK" = true ] ; then | |
|
|
73 | install_readonly files/sysctl.d/83-rpi-printk.conf "${ETC_DIR}/sysctl.d/83-rpi-printk.conf" | |
|
|
84 | 74 | fi |
|
|
85 | 75 | |
|
|
86 | # Install firmware boot cmdline | |
|
|
87 | echo "${CMDLINE}" > "${BOOT_DIR}/cmdline.txt" | |
|
|
76 | # Install udev rule for serial alias | |
|
|
77 | install_readonly files/etc/99-com.rules "${ETC_DIR}/udev/rules.d/99-com.rules" | |
|
|
88 | 78 | |
|
|
89 | # Install firmware config | |
|
|
90 | install_readonly files/boot/config.txt "${BOOT_DIR}/config.txt" | |
|
|
79 | if [ "$RPI_MODEL" = 0 ] || [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then | |
|
|
91 | 80 | |
|
|
92 | # Setup minimal GPU memory allocation size: 16MB (no X) | |
|
|
93 | if [ "$ENABLE_MINGPU" = true ] ; then | |
|
|
94 | echo "gpu_mem=16" >> "${BOOT_DIR}/config.txt" | |
|
|
95 | fi | |
|
|
96 | ||
|
|
97 | # Setup boot with initramfs | |
|
|
98 | if [ "$ENABLE_INITRAMFS" = true ] ; then | |
|
|
99 | echo "initramfs initramfs-${KERNEL_VERSION} followkernel" >> "${BOOT_DIR}/config.txt" | |
|
|
100 | fi | |
|
|
101 | ||
|
|
102 | # Disable RPi3 Bluetooth and restore ttyAMA0 serial device | |
|
|
103 | if [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then | |
|
|
104 | if [ "$ENABLE_CONSOLE" = true ] && [ "$ENABLE_UBOOT" = false ] ; then | |
|
|
105 | echo "dtoverlay=pi3-disable-bt" >> "${BOOT_DIR}/config.txt" | |
|
|
106 | echo "enable_uart=1" >> "${BOOT_DIR}/config.txt" | |
|
|
107 | fi | |
|
|
108 | fi | |
|
|
81 | # RPI0,3,3P Use default ttyS0 (mini-UART)as serial interface | |
|
|
82 | SET_SERIAL="ttyS0" | |
|
|
109 | 83 | |
|
|
84 | # Bluetooth enabled | |
|
|
110 | 85 | if [ "$ENABLE_BLUETOOTH" = true ] ; then |
|
|
111 | 86 | # Create temporary directory for Bluetooth sources |
|
|
112 | 87 | temp_dir=$(as_nobody mktemp -d) |
| @@ -117,8 +92,6 if [ "$ENABLE_BLUETOOTH" = true ] ; then | |||
|
|
117 | 92 | # Copy downloaded sources |
|
|
118 | 93 | mv "${temp_dir}/pi-bluetooth" "${R}/tmp/" |
|
|
119 | 94 | |
|
|
120 | # Raspberry-sys-mod package for /dev/serial device needed by bluetooth service | |
|
|
121 | as_nobody wget -q -O "${R}/tmp/pi-bluetooth/99-com.rules" https://raw.githubusercontent.com/RPi-Distro/raspberrypi-sys-mods/master/etc.armhf/udev/rules.d/99-com.rules | |
|
|
122 | 95 | # Bluetooth firmware from arch aur https://aur.archlinux.org/packages/pi-bluetooth/ |
|
|
123 | 96 | as_nobody wget -q -O "${R}/tmp/pi-bluetooth/LICENCE.broadcom_bcm43xx" https://aur.archlinux.org/cgit/aur.git/plain/LICENCE.broadcom_bcm43xx?h=pi-bluetooth |
|
|
124 | 97 | as_nobody wget -q -O "${R}/tmp/pi-bluetooth/BCM43430A1.hcd" https://aur.archlinux.org/cgit/aur.git/plain/BCM43430A1.hcd?h=pi-bluetooth |
| @@ -139,11 +112,76 if [ "$ENABLE_BLUETOOTH" = true ] ; then | |||
|
|
139 | 112 | install_readonly "${R}/tmp/pi-bluetooth/BCM43430A1.hcd" "${ETC_DIR}/firmware/LICENCE.broadcom_bcm43xx" |
|
|
140 | 113 | install_readonly "${R}/tmp/pi-bluetooth/debian/pi-bluetooth.bthelper@.service" "${ETC_DIR}/systemd/system/pi-bluetooth.bthelper@.service" |
|
|
141 | 114 | install_readonly "${R}/tmp/pi-bluetooth/debian/pi-bluetooth.hciuart.service" "${ETC_DIR}/systemd/system/pi-bluetooth.hciuart.service" |
|
|
142 | # Install udev rule for bluetooth device | |
|
|
143 | install_readonly "${R}/tmp/pi-bluetooth/99-com.rules" "${ETC_DIR}/udev/rules.d/99-com.rules" | |
|
|
144 | 115 | |
|
|
145 | 116 | # Remove temporary directory |
|
|
146 | 117 | rm -fr "${temp_dir}" |
|
|
118 | ||
|
|
119 | # Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore UART0/ttyAMA0 over GPIOs 14 & 15. Slow Bluetooth and slow cpu. Use /dev/ttyS0 instead of /dev/ttyAMA0 | |
|
|
120 | if [ "$ENABLE_MINIUART_OVERLAY" = true ] ; then | |
|
|
121 | ||
|
|
122 | # set overlay to swap ttyAMA0 and ttyS0 | |
|
|
123 | echo "dtoverlay=pi3-miniuart-bt" >> "${BOOT_DIR}/config.txt" | |
|
|
124 | ||
|
|
125 | # if force_turbo didn't lock cpu at high speed, lock it at low speed (XOR logic) or miniuart will be broken | |
|
|
126 | if [ "$ENABLE_TURBO" = false ] ; then | |
|
|
127 | echo "core_freq=250" >> "${BOOT_DIR}/config.txt" | |
|
|
128 | fi | |
|
|
129 | fi | |
|
|
130 | ||
|
|
131 | else # if ENABLE_BLUETOOTH = false | |
|
|
132 | # set overlay to disable bluetooth | |
|
|
133 | echo "dtoverlay=pi3-disable-bt" >> "${BOOT_DIR}/config.txt" | |
|
|
134 | fi # ENABLE_BLUETOOTH end | |
|
|
135 | ||
|
|
136 | else | |
|
|
137 | # RPI1,1P,2 Use default ttyAMA0 (full UART) as serial interface | |
|
|
138 | SET_SERIAL="ttyAMA0" | |
|
|
139 | fi | |
|
|
140 | ||
|
|
141 | # may need sudo systemctl disable hciuart | |
|
|
142 | if [ "$ENABLE_CONSOLE" = true ] ; then | |
|
|
143 | echo "enable_uart=1" >> "${BOOT_DIR}/config.txt" | |
|
|
144 | ||
|
|
145 | # add string to cmdline | |
|
|
146 | CMDLINE="${CMDLINE} console=serial0,115200" | |
|
|
147 | ||
|
|
148 | # Enable serial console systemd style | |
|
|
149 | chroot_exec systemctl start serial-getty@"$SET_SERIAL".service | |
|
|
150 | chroot_exec systemctl enable serial-getty@"$SET_SERIAL".service | |
|
|
151 | else | |
|
|
152 | echo "enable_uart=0" >> "${BOOT_DIR}/config.txt" | |
|
|
153 | ||
|
|
154 | # Enable serial console systemd style | |
|
|
155 | chroot_exec systemctl stop serial-getty@"$SET_SERIAL".service | |
|
|
156 | chroot_exec systemctl disable serial-getty@"$SET_SERIAL".service | |
|
|
157 | fi | |
|
|
158 | ||
|
|
159 | # Remove IPv6 networking support | |
|
|
160 | if [ "$ENABLE_IPV6" = false ] ; then | |
|
|
161 | CMDLINE="${CMDLINE} ipv6.disable=1" | |
|
|
162 | fi | |
|
|
163 | ||
|
|
164 | # Automatically assign predictable network interface names | |
|
|
165 | if [ "$ENABLE_IFNAMES" = false ] ; then | |
|
|
166 | CMDLINE="${CMDLINE} net.ifnames=0" | |
|
|
167 | else | |
|
|
168 | CMDLINE="${CMDLINE} net.ifnames=1" | |
|
|
169 | fi | |
|
|
170 | ||
|
|
171 | # Install firmware boot cmdline | |
|
|
172 | echo "${CMDLINE}" > "${BOOT_DIR}/cmdline.txt" | |
|
|
173 | ||
|
|
174 | # Install firmware config | |
|
|
175 | install_readonly files/boot/config.txt "${BOOT_DIR}/config.txt" | |
|
|
176 | ||
|
|
177 | # Setup minimal GPU memory allocation size: 16MB (no X) | |
|
|
178 | if [ "$ENABLE_MINGPU" = true ] ; then | |
|
|
179 | echo "gpu_mem=16" >> "${BOOT_DIR}/config.txt" | |
|
|
180 | fi | |
|
|
181 | ||
|
|
182 | # Setup boot with initramfs | |
|
|
183 | if [ "$ENABLE_INITRAMFS" = true ] ; then | |
|
|
184 | echo "initramfs initramfs-${KERNEL_VERSION} followkernel" >> "${BOOT_DIR}/config.txt" | |
|
|
147 | 185 | fi |
|
|
148 | 186 | |
|
|
149 | 187 | # Create firmware configuration and cmdline symlinks |
| @@ -22,8 +22,3 else | |||
|
|
22 | 22 | # Set no root password to disable root login |
|
|
23 | 23 | chroot_exec usermod -p \'!\' root |
|
|
24 | 24 | fi |
|
|
25 | ||
|
|
26 | # Enable serial console systemd style | |
|
|
27 | if [ "$ENABLE_CONSOLE" = true ] ; then | |
|
|
28 | chroot_exec systemctl enable serial-getty\@ttyAMA0.service | |
|
|
29 | fi | |
| @@ -112,7 +112,9 APT_PROXY=${APT_PROXY:=""} | |||
|
|
112 | 112 | APT_SERVER=${APT_SERVER:="ftp.debian.org"} |
|
|
113 | 113 | |
|
|
114 | 114 | # Feature settings |
|
|
115 | ENABLE_PRINTK=${ENABLE_PRINTK:=false} | |
|
|
115 | 116 | ENABLE_BLUETOOTH=${ENABLE_BLUETOOTH:=false} |
|
|
117 | ENABLE_MINIUART_OVERLAY=${ENABLE_MINIUART_OVERLAY:=false} | |
|
|
116 | 118 | ENABLE_CONSOLE=${ENABLE_CONSOLE:=true} |
|
|
117 | 119 | ENABLE_I2C=${ENABLE_I2C:=false} |
|
|
118 | 120 | ENABLE_SPI=${ENABLE_SPI:=false} |
| @@ -214,7 +216,7 set +x | |||
|
|
214 | 216 | |
|
|
215 | 217 | #Check if apt-cacher-ng has port 3142 open and set APT_PROXY |
|
|
216 | 218 | APT_CACHER_RUNNING=$(lsof -i :3142 | grep apt-cacher-ng | cut -d ' ' -f3 | uniq) |
|
|
217 | if [ -n ${APT_CACHER_RUNNING} ] ; then | |
|
|
219 | if [ -n "${APT_CACHER_RUNNING}" ] ; then | |
|
|
218 | 220 | APT_PROXY=http://127.0.0.1:3142/ |
|
|
219 | 221 | fi |
|
|
220 | 222 | |
| @@ -322,32 +324,28 case "$RPI_MODEL" in | |||
|
|
322 | 324 | ;; |
|
|
323 | 325 | esac |
|
|
324 | 326 | |
|
|
325 | # Prepare date string for default image file name | |
|
|
326 | DATE="$(date +%Y-%m-%d)" | |
|
|
327 | if [ -z "$KERNEL_BRANCH" ] ; then | |
|
|
328 | IMAGE_NAME=${IMAGE_NAME:=${BASEDIR}/${DATE}-${KERNEL_ARCH}-CURRENT-rpi${RPI_MODEL}-${RELEASE}-${RELEASE_ARCH}} | |
|
|
329 | else | |
|
|
330 | IMAGE_NAME=${IMAGE_NAME:=${BASEDIR}/${DATE}-${KERNEL_ARCH}-${KERNEL_BRANCH}-rpi${RPI_MODEL}-${RELEASE}-${RELEASE_ARCH}} | |
|
|
331 | fi | |
|
|
332 | ||
|
|
327 | # Raspberry PI 0,3,3P with Bluetooth and Wifi onboard | |
|
|
333 | 328 | if [ "$RPI_MODEL" = 0 ] || [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then |
|
|
334 | 329 | # Include bluetooth packages on supported boards |
|
|
335 | 330 | if [ "$ENABLE_BLUETOOTH" = true ] && [ "$ENABLE_CONSOLE" = false ]; then |
|
|
336 | 331 | APT_INCLUDES="${APT_INCLUDES},bluetooth,bluez" |
|
|
337 | 332 | fi |
|
|
338 | # Check if console or bluetooth configuration is invalid on RPI 0,3,3P | |
|
|
339 | if [ "$ENABLE_BLUETOOTH" = true ] && [ "$ENABLE_CONSOLE" = true ]; then | |
|
|
340 | echo "error: ENABLE_BLUETOOTH and ENABLE_CONSOLE can't be active on the same time." | |
|
|
341 | exit 1 | |
|
|
342 | fi | |
|
|
343 | else # if [ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] || [ "$RPI_MODEL" = 2 ] ; then | |
|
|
333 | else # Raspberry PI 1,1P,2 without Wifi and bluetooth onboard | |
|
|
344 | 334 |
|
|
|
345 |
|
|
|
|
346 |
|
|
|
|
335 | if [ "$ENABLE_WIRELESS" = true ] || [ "$ENABLE_BLUETOOTH" = true ]; then | |
|
|
336 | echo "error: The selected Raspberry Pi model has no integrated interface for wireless or bluetooth" | |
|
|
347 | 337 |
|
|
|
348 | 338 | fi |
|
|
349 | 339 | fi |
|
|
350 | 340 | |
|
|
341 | # Prepare date string for default image file name | |
|
|
342 | DATE="$(date +%Y-%m-%d)" | |
|
|
343 | if [ -z "$KERNEL_BRANCH" ] ; then | |
|
|
344 | IMAGE_NAME=${IMAGE_NAME:=${BASEDIR}/${DATE}-${KERNEL_ARCH}-CURRENT-rpi${RPI_MODEL}-${RELEASE}-${RELEASE_ARCH}} | |
|
|
345 | else | |
|
|
346 | IMAGE_NAME=${IMAGE_NAME:=${BASEDIR}/${DATE}-${KERNEL_ARCH}-${KERNEL_BRANCH}-rpi${RPI_MODEL}-${RELEASE}-${RELEASE_ARCH}} | |
|
|
347 | fi | |
|
|
348 | ||
|
|
351 | 349 | # Check if DISABLE_UNDERVOLT_WARNINGS parameter value is supported |
|
|
352 | 350 | if [ -n "$DISABLE_UNDERVOLT_WARNINGS" ] ; then |
|
|
353 | 351 | if [ "$DISABLE_UNDERVOLT_WARNINGS" != 1 ] && [ "$DISABLE_UNDERVOLT_WARNINGS" != 2 ] ; then |
General Comments 0
Vous devez vous connecter pour laisser un commentaire.
Se connecter maintenant
