| @@ -243,6 +243,7 if [ -n "$SET_ARCH" ] ; then | |||||
| 243 |
|
243 | |||
| 244 | #Raspberry setting grouped by board compability |
|
244 | #Raspberry setting grouped by board compability | |
| 245 | if [ "$RPI_MODEL" = 0 ] || [ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] ; then |
|
245 | if [ "$RPI_MODEL" = 0 ] || [ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] ; then | |
|
|
246 | echo "Setting settings for bcm2835 Raspberry PI boards" | |||
| 246 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-armel" |
|
247 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-armel" | |
| 247 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcmrpi_defconfig} |
|
248 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcmrpi_defconfig} | |
| 248 | UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_defconfig} |
|
249 | UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_defconfig} | |
| @@ -251,12 +252,16 if [ -n "$SET_ARCH" ] ; then | |||||
| 251 | CROSS_COMPILE=${CROSS_COMPILE:=arm-linux-gnueabi-} |
|
252 | CROSS_COMPILE=${CROSS_COMPILE:=arm-linux-gnueabi-} | |
| 252 | fi |
|
253 | fi | |
| 253 | if [ "$RPI_MODEL" = 2 ] || [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then |
|
254 | if [ "$RPI_MODEL" = 2 ] || [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ] ; then | |
|
|
255 | echo "Setting settings for bcm2837 Raspberry PI boards" | |||
| 254 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-armhf" |
|
256 | REQUIRED_PACKAGES="${REQUIRED_PACKAGES} crossbuild-essential-armhf" | |
| 255 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcm2709_defconfig} |
|
257 | KERNEL_DEFCONFIG=${KERNEL_DEFCONFIG:=bcm2709_defconfig} | |
| 256 | RELEASE_ARCH=${RELEASE_ARCH:=armhf} |
|
258 | RELEASE_ARCH=${RELEASE_ARCH:=armhf} | |
| 257 | KERNEL_IMAGE=${KERNEL_IMAGE:=kernel7.img} |
|
259 | KERNEL_IMAGE=${KERNEL_IMAGE:=kernel7.img} | |
| 258 | CROSS_COMPILE=${CROSS_COMPILE:=arm-linux-gnueabihf-} |
|
260 | CROSS_COMPILE=${CROSS_COMPILE:=arm-linux-gnueabihf-} | |
| 259 | fi |
|
261 | fi | |
|
|
262 | ||||
|
|
263 | echo "Setting Raspberry PI $RPI_MODEL specific configuration" | |||
|
|
264 | ||||
| 260 | #Device specific configuration |
|
265 | #Device specific configuration | |
| 261 | case "$RPI_MODEL" in |
|
266 | case "$RPI_MODEL" in | |
| 262 | 0) |
|
267 | 0) | |
| @@ -286,35 +291,6 if [ -n "$SET_ARCH" ] ; then | |||||
| 286 | ;; |
|
291 | ;; | |
| 287 | esac |
|
292 | esac | |
| 288 |
|
293 | |||
| 289 | #Device specific configuration |
|
|||
| 290 | # if [ "$RPI_MODEL" = 0 ] ; then |
|
|||
| 291 | # DTB_FILE=${DTB_FILE:=bcm2708-rpi-0-w.dtb} |
|
|||
| 292 | # fi |
|
|||
| 293 | # if [ "$RPI_MODEL" = 1 ] ; then |
|
|||
| 294 | # DTB_FILE=${DTB_FILE:=bcm2708-rpi-b.dtb} |
|
|||
| 295 | # fi |
|
|||
| 296 | # if [ "$RPI_MODEL" = 1P ] ; then |
|
|||
| 297 | # DTB_FILE=${DTB_FILE:=bcm2708-rpi-b-plus.dtb} |
|
|||
| 298 | # fi |
|
|||
| 299 | # if [ "$RPI_MODEL" = 2 ] ; then |
|
|||
| 300 | # DTB_FILE=${DTB_FILE:=bcm2709-rpi-2-b.dtb} |
|
|||
| 301 | # UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_2_defconfig} |
|
|||
| 302 | # #Precompiled Kernel rpi2 |
|
|||
| 303 | # #COLLABORA_KERNEL=${COLLABORA_KERNEL:=3.18.0-trunk-rpi2} |
|
|||
| 304 | # fi |
|
|||
| 305 | # if [ "$RPI_MODEL" = 3 ] ; then |
|
|||
| 306 | # DTB_FILE=${DTB_FILE:=bcm2710-rpi-3-b.dtb} |
|
|||
| 307 | # UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_3_32b_defconfig} |
|
|||
| 308 | # fi |
|
|||
| 309 | # if [ "$RPI_MODEL" = 3P ] ; then |
|
|||
| 310 | # DTB_FILE=${DTB_FILE:=bcm2710-rpi-3-b.dtb} |
|
|||
| 311 | # UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_3_32b_defconfig} |
|
|||
| 312 | # fi |
|
|||
| 313 | # if [ -z "$RPI_MODEL" ] ; then |
|
|||
| 314 | # echo "error: Raspberry Pi model $RPI_MODEL is not set!" |
|
|||
| 315 | # exit 1 |
|
|||
| 316 | # fi |
|
|||
| 317 |
|
||||
| 318 | #end 32 bit |
|
294 | #end 32 bit | |
| 319 | fi |
|
295 | fi | |
| 320 | #SET_ARCH not set |
|
296 | #SET_ARCH not set | |
| @@ -324,12 +300,14 else | |||||
| 324 | fi |
|
300 | fi | |
| 325 |
|
301 | |||
| 326 | # Check if the internal wireless interface is supported by the RPi model |
|
302 | # Check if the internal wireless interface is supported by the RPi model | |
| 327 | if [ "$ENABLE_WIRELESS" = true ] && { [ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] || [ "$RPI_MODEL" = 2 ] ; } ; then |
|
303 | if [ "$ENABLE_WIRELESS" = true ] ; then | |
| 328 | echo "error: The selected Raspberry Pi model has no internal wireless interface" |
|
304 | if [ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] || [ "$RPI_MODEL" = 2 ] ; then | |
| 329 | exit 1 |
|
305 | echo "error: The selected Raspberry Pi model has no internal wireless interface" | |
| 330 | else |
|
306 | exit 1 | |
| 331 | echo "Raspberry Pi model" |
|
307 | else | |
| 332 | fi |
|
308 | echo "Raspberry Pi model" | |
|
|
309 | fi | |||
|
|
310 | fi | |||
| 333 |
|
311 | |||
| 334 | # Check if DISABLE_UNDERVOLT_WARNINGS parameter value is supported |
|
312 | # Check if DISABLE_UNDERVOLT_WARNINGS parameter value is supported | |
| 335 | if [ -n "$DISABLE_UNDERVOLT_WARNINGS" ] ; then |
|
313 | if [ -n "$DISABLE_UNDERVOLT_WARNINGS" ] ; then | |
General Comments 0
Vous devez vous connecter pour laisser un commentaire.
Se connecter maintenant
