| @@ -135,17 +135,17 ln -sf firmware/config.txt "${R}/boot/config.txt" | |||
|
|
135 | 135 | ln -sf firmware/cmdline.txt "${R}/boot/cmdline.txt" |
|
|
136 | 136 | |
|
|
137 | 137 | # Install and setup kernel modules to load at boot |
|
|
138 |
mkdir -p "${R} |
|
|
|
139 |
install_readonly files/modules/rpi2.conf "${R} |
|
|
|
138 | mkdir -p "${LIB_DIR}/modules-load.d/" | |
|
|
139 | install_readonly files/modules/rpi2.conf "${LIB_DIR}/modules-load.d/rpi2.conf" | |
|
|
140 | 140 | |
|
|
141 | 141 | # Load hardware random module at boot |
|
|
142 | 142 | if [ "$ENABLE_HWRANDOM" = true ] && [ "$BUILD_KERNEL" = false ] ; then |
|
|
143 |
sed -i "s/^# bcm2708_rng/bcm2708_rng/" "${R} |
|
|
|
143 | sed -i "s/^# bcm2708_rng/bcm2708_rng/" "${LIB_DIR}/modules-load.d/rpi2.conf" | |
|
|
144 | 144 | fi |
|
|
145 | 145 | |
|
|
146 | 146 | # Load sound module at boot |
|
|
147 | 147 | if [ "$ENABLE_SOUND" = true ] ; then |
|
|
148 |
sed -i "s/^# snd_bcm2835/snd_bcm2835/" "${R} |
|
|
|
148 | sed -i "s/^# snd_bcm2835/snd_bcm2835/" "${LIB_DIR}/modules-load.d/rpi2.conf" | |
|
|
149 | 149 | else |
|
|
150 | 150 | echo "dtparam=audio=off" >> "${BOOT_DIR}/config.txt" |
|
|
151 | 151 | fi |
| @@ -153,16 +153,16 fi | |||
|
|
153 | 153 | # Enable I2C interface |
|
|
154 | 154 | if [ "$ENABLE_I2C" = true ] ; then |
|
|
155 | 155 | echo "dtparam=i2c_arm=on" >> "${BOOT_DIR}/config.txt" |
|
|
156 |
sed -i "s/^# i2c-bcm2708/i2c-bcm2708/" "${R} |
|
|
|
157 |
sed -i "s/^# i2c-dev/i2c-dev/" "${R} |
|
|
|
156 | sed -i "s/^# i2c-bcm2708/i2c-bcm2708/" "${LIB_DIR}/modules-load.d/rpi2.conf" | |
|
|
157 | sed -i "s/^# i2c-dev/i2c-dev/" "${LIB_DIR}/modules-load.d/rpi2.conf" | |
|
|
158 | 158 | fi |
|
|
159 | 159 | |
|
|
160 | 160 | # Enable SPI interface |
|
|
161 | 161 | if [ "$ENABLE_SPI" = true ] ; then |
|
|
162 | 162 | echo "dtparam=spi=on" >> "${BOOT_DIR}/config.txt" |
|
|
163 |
echo "spi-bcm2708" >> "${R} |
|
|
|
163 | echo "spi-bcm2708" >> "${LIB_DIR}/modules-load.d/rpi2.conf" | |
|
|
164 | 164 | if [ "$RPI_MODEL" = 3 ] || [ "$RPI_MODEL" = 3P ]; then |
|
|
165 |
sed -i "s/spi-bcm2708/spi-bcm2835/" "${R} |
|
|
|
165 | sed -i "s/spi-bcm2708/spi-bcm2835/" "${LIB_DIR}/modules-load.d/rpi2.conf" | |
|
|
166 | 166 | fi |
|
|
167 | 167 | fi |
|
|
168 | 168 | |
General Comments 0
Vous devez vous connecter pour laisser un commentaire.
Se connecter maintenant
