Raspi2-3_GenImage Commit - r431:d23b6c103389 · Collaboration Tremplin des Sciences

- removed wrong/old logic for locales...

Unknown -

r431:d23b6c103389

parent child

Context file:

r431:d23b6c103389

Collapse all files

README.md +1 -1

              #### Basic system features:
              ##### `ENABLE_CONSOLE`=true
-             Enable serial console interface. Recommended if no monitor or keyboard is connected to the RPi2/3. In case of problems fe. if the network (auto) configuration failed - the serial console can be used to access the system.
+             Enable serial console interface. Recommended if no monitor or keyboard is connected to the RPi2/3. In case of problems fe. if the network (auto) configuration failed - the serial console can be used to access the system. On `RPI_MODEL= 0,3,3P` - Bluetooth gets auto enabled if `ENABLE_CONSOLE` and `ENABLE_UBOOT` are set to `false`
              ##### `ENABLE_I2C`=false
              Enable I2C interface on the RPi2/3. Please check the [RPi2/3 pinout diagrams](https://elinux.org/RPi_Low-level_peripherals) to connect the right GPIO pins.

bootstrap.d/12-locale.sh +2 -2

                chroot_exec update-locale LANG="${DEFLOCAL}"
                # Install and setup default keyboard configuration
-               if [ "$XKB_MODEL" != "pc105" ] ; then
+               if [ "$XKB_MODEL" != "" ] ; then
                  sed -i "s/^XKBMODEL.*/XKBMODEL=\"${XKB_MODEL}\"/" "${ETC_DIR}/default/keyboard"
                fi
-               if [ "$XKB_LAYOUT" != "us" ] ; then
+               if [ "$XKB_LAYOUT" != "" ] ; then
                  sed -i "s/^XKBLAYOUT.*/XKBLAYOUT=\"${XKB_LAYOUT}\"/" "${ETC_DIR}/default/keyboard"
                fi
                if [ "$XKB_VARIANT" != "" ] ; then

bootstrap.d/41-uboot.sh +2 -2

                fi
                # Set mkfile to use the correct dtb file
-               sed -i "s/^\(setenv dtbfile \).*/\1${DTB_FILE}/" "${BOOT_DIR}/uboot.mkimage"
+               sed -i "s|bcm2709-rpi-2-b.dtb|${DTB_FILE}|" "${BOOT_DIR}/uboot.mkimage"
                # Set mkfile to use the correct mach id
                if [ "$ENABLE_QEMU" = true ] ; then
                fi
                # Set mkfile to use kernel image
-               sed -i "s/^\(fatload mmc 0:1 \${kernel_addr_r} \).*/\1${KERNEL_IMAGE}/" "${BOOT_DIR}/uboot.mkimage"
+               sed -i "s|kernel7.img|${KERNEL_IMAGE}|" "${BOOT_DIR}/uboot.mkimage"
                # Remove all leading blank lines
                sed -i "/./,\$!d" "${BOOT_DIR}/uboot.mkimage"

rpi23-gen-image.sh +40 -36

              BLUETOOTH_URL=${BLUETOOTH_URL:=https://github.com/RPi-Distro/pi-bluetooth.git}
              # Build directories
-             BASEDIR=${BASEDIR:=$(pwd)/images/${RELEASE}}
+             WORKDIR=$(pwd)
+             BASEDIR=${BASEDIR:=${WORKDIR}/images/${RELEASE}}
              BUILDDIR="${BASEDIR}/build"
              # Chroot directories
              # Packages required in the chroot build environment
              APT_INCLUDES=${APT_INCLUDES:=""}
-             APT_INCLUDES="${APT_INCLUDES},apt-transport-https,apt-utils,ca-certificates,debian-archive-keyring,dialog,sudo,systemd,sysvinit-utils,locales,keyboard-configuration,console-setup"
+             APT_INCLUDES="${APT_INCLUDES},apt-transport-https,apt-utils,ca-certificates,debian-archive-keyring,dialog,sudo,systemd,sysvinit-utils,locales,keyboard-configuration,console-setup,libnss-systemd"
              # Packages to exclude from chroot build environment
              APT_EXCLUDES=${APT_EXCLUDES:=""}
              set +x
+             #Check if apt-cacher-ng has its default port open on and set APT_PROXY
+             if [ -n "$(lsof -i :3142)" ] ; then
+             HTTP_PROXY=http://127.0.0.1:3142/
+             fi
              # Setup architecture specific settings
              if [ -n "$SET_ARCH" ] ; then
                # 64 bit configuration
                echo "error: Please set '32' or '64' as value for SET_ARCH"
                exit 1
              fi
-                 # Device specific configuration and U-Boot configuration
-                 case "$RPI_MODEL" in
-)
-                   DTB_FILE=${DTB_FILE:=bcm2708-rpi-0-w.dtb}
-                   UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_defconfig}
-                   ;;
-)
-                   DTB_FILE=${DTB_FILE:=bcm2708-rpi-b.dtb}
-                   UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_defconfig}
-                   ;;
-P)
-                   DTB_FILE=${DTB_FILE:=bcm2708-rpi-b-plus.dtb}
-                   UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_defconfig}
-                   ;;
-)
-                   DTB_FILE=${DTB_FILE:=bcm2709-rpi-2-b.dtb}
-                   UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_2_defconfig}
-                   ;;
-)
-                   DTB_FILE=${DTB_FILE:=bcm2710-rpi-3-b.dtb}
-                   UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_3_defconfig}
-                   ;;
-P)
-                   DTB_FILE=${DTB_FILE:=bcm2710-rpi-3-b.dtb}
-                   UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_3_defconfig}
-                   ;;
-                 *)
-                   echo "error: Raspberry Pi model $RPI_MODEL is not supported!"
-                   exit 1
-                   ;;
-                 esac
+             # Device specific configuration and U-Boot configuration
+             case "$RPI_MODEL" in
+)
+                 DTB_FILE=${DTB_FILE:=bcm2708-rpi-0-w.dtb}
+                 UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_defconfig}
+                 ;;
+)
+                 DTB_FILE=${DTB_FILE:=bcm2708-rpi-b.dtb}
+                 UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_defconfig}
+                 ;;
+P)
+                 DTB_FILE=${DTB_FILE:=bcm2708-rpi-b-plus.dtb}
+                 UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_defconfig}
+                 ;;
+)
+                 DTB_FILE=${DTB_FILE:=bcm2709-rpi-2-b.dtb}
+                 UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_2_defconfig}
+                 ;;
+)
+                 DTB_FILE=${DTB_FILE:=bcm2710-rpi-3-b.dtb}
+                 UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_3_defconfig}
+                 ;;
+P)
+                 DTB_FILE=${DTB_FILE:=bcm2710-rpi-3-b.dtb}
+                 UBOOT_CONFIG=${UBOOT_CONFIG:=rpi_3_defconfig}
+                 ;;
+               *)
+                 echo "error: Raspberry Pi model $RPI_MODEL is not supported!"
+                 exit 1
+                 ;;
+             esac
              # Prepare date string for default image file name
              DATE="$(date +%Y-%m-%d)"
                if [ "$RPI_MODEL" = 1 ] || [ "$RPI_MODEL" = 1P ] || [ "$RPI_MODEL" = 2 ] ; then
                  echo "error: The selected Raspberry Pi model has no internal wireless interface"
                  exit 1
-               else
-                 echo "Raspberry Pi $RPI_MODEL has WIFI support"
                fi
              fi
              # Check if all required packages are installed on the build system
              for package in $REQUIRED_PACKAGES ; do
-               if [ "$(dpkg-query -W -f='${Status}' $package)" != "install ok installed" ] ; then
+               if [ "$(dpkg-query -W -f='${Status}' "$package")" != "install ok installed" ] ; then
                  MISSING_PACKAGES="${MISSING_PACKAGES} $package"
                fi
              done

General Comments 0

Écrire
Preview

Vous devez vous connecter pour laisser un commentaire. Se connecter maintenant

No TODOs yet

	Site-wide shortcuts
/	Use quick search box
g h	Goto home page
g g	Goto my private gists page
g G	Goto my public gists page
g 0-9	Goto bookmarked items from 0-9
n r	New repository page
n g	New gist page

	Dépôts
g s	Goto summary page
g c	Goto changelog page
g f	Goto files page
g F	Goto files page with file search activated
g p	Goto pull requests page
g o	Goto repository settings
g O	Goto repository access permissions settings
t s	Toggle sidebar on some pages